Book Service

 

 

We've discovered the article involving Tools You Need to Install a New Bathtub below on the internet and decided it made sense to write about it with you on my blog.

Setting up a bath tub isn't exactly rocket science, but it does need strong plumbing, woodworking, and also often, tiling skills. Replacing an old bath tub with a new one is also a reasonably difficult job. If the old tub is easily easily accessible, the project can relocate speedily; if you have to open up a wall surface to get rid of the old tub as well as place the new bath tub, the task is much harder. In either instance, the project is within a home handyman's abilities, although you will certainly require a helper to move out the old bathtub and also embeded in the brand-new one. See to it you have qualified yourself for the work and also are comfortable attempting it. Rather than employing a specialist to take over a halfway-completed task, it is much better to consider employing one before you start. Chances are you might need an expert plumber to make tube connections.
This write-up will certainly aid you mount a brand-new tub in your shower room if you have already bought a brand-new bathtub as well as don't need to change the setup of your previous water pipelines.
Your tools and product list must comprise the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipeline Caps


 

Getting ready for the Installation

To start with, the supporting frame provided with the bathroom ought to be fitted (if required) according to the supplier's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to see to it that if the faucet comes with a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps device to avoid strain on the tub.
Fit the flexible faucet connectors to the bottom of both taps utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you make use of all of the provided washing machines.
Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must now be ready to be suited its final position.

 

 

Removing Old Touches

If you require to replace old faucets with new ones as a part of your setup, after that the first thing you should do is detach the water. After doing so, turn on the faucets to drain any type of water remaining in the system. The process of removing the existing taps can be fairly problematic as a result of the restricted accessibility that is commonly the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the faucets. Have a cloth ready for the staying water that will certainly come from the pipelines. When the supply pipelines have actually been gotten rid of, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from turning during this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any kind of old securing compound.
Before proceeding to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new taps to fit.

 

 

Setting up the Tub

Making use of both wood boards under its feet, position the bathtub in the required position. The wooden boards are valuable in uniformly spreading the weight of the tub over the area of the boards instead of focusing all the weight onto four small points.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the tub up until the spirit level checks out level.
To install taps, fit the bottom of the furthest flexible faucet port to the proper supply pipe by making a compression join; then do the very same for the various other faucet.
Activate the water and also examine all joints and also brand-new pipework for leaks as well as tighten them if required. Fill the bathtub as well as additionally examine the overflow electrical outlet as well as the normal outlet for leakages.
Ultimately, take care of the bath paneling as described in the producer's instruction manual. Tiling and also securing around the bathtub should wait until the bath tub has actually been utilized at least once as this will certainly resolve it into its final position.

 

 

Suitable New Touches

If the tails of the new taps are plastic, after that you will certainly need a plastic adapter to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin making certain that the washers remain in location between the faucet as well as the sink. Secure the faucet in place with the manufacturer supplied backnut. When the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with regular tap adapters. The former type must be connected to the faucet ends initially, tightening just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.

 

 

Tiling Around the Bath tub

In the area where the bath satisfies the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to split a rigid seal, causing the water to permeate the wall between the bathroom and the tiling, bring about problems with wetness and feasible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your fixtures and also fittings. They are offered in tubes and also cartridges, and can securing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill the bathtub with water prior to securing, to allow for the motion experienced when the bathtub remains in use. The sealer can fracture rather early if you do not take into consideration this activity before sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily offered on the marketplace. It is suggested to fit the tiles using waterproof or water-proof glue and also grout.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

We were brought to that editorial on Tools You Need to Install a New Bathtub through someone on another domain. Are you aware of another person who is excited about the topic? Please feel free to share it. We cherish reading our article about A Step-by-Step Guide to Installing a Bathtub.

Customer Reviews